Skip to main content
Header Main Image

Our new products

Quarter turn for quick mounting and freely designed foil

EMKA extends its range of quarter turns for quick mounting. The new quarter turn for quick mounting comes with a housing plate with a custom-made foil that shows e.g. a company logo or a material imitation like matt chrome, brushed stainless steel or any other optic. EMKA uses the In-Mold-Labeling process (IML) to firmly connect the foil with the housing plate in just one operation during the plastic injection molding. The results of the IML are custom-made foiled plates for the polyamide quarter turns with surfaces that are both sturdy and ambitious. The quarter turn for quick mounting can be snapped-in in only 2 steps within a few seconds and also change its locking direction easily from left to right.

Product features at a glance:​

  • Pre-assembled insert unit - housing plate of polyamide GF, insert of zinc-die​
  • Quick snap-in assembly without tools saves up to 80% assembly time
  • On request, housing plate with freely designed foil e.g. company logo and/or material imitation
  • Various inserts in stock (further inserts on request)
  • Housing with integrated com of polyamide GF​
  • Self-sealing construction with integrated TPE seal onto the back of housing plate (IP 69K)
  • Used at door thickness from 1.0 mm until 3.0 mm (Ts including surface coating)
  • Standard cut out ⃞ 20.1 rounded up 22.5, Program 1000
  • Patented​
  • Design protected​
Assembly videoYoutube(mp4 | 27,7 MB)
Modification video for door right hand versionYoutube(mp4 | 27,3 MB)
Disassemble videoYoutube(mp4 | 27,6 MB)
Quarter turn for quick mounting and freely designed foil​, Matt chrome look​
Matt chrome look​
Quarter turn for quick mounting and freely designed foil​, Brushed stainless steel look
Brushed stainless steel look
Quarter turn for quick mounting, Design example
Design example
Quarter turn for quick mounting, Design example
Design example
Quarter turn for quick mounting and freely designed foil​, Black
Quarter turn for quick mounting - Black
Quarter turn for quick mounting, assembly
Quarter turn for quick mounting

Program 1031 - new 120° hinge solution

Extension of our product range by another hinge solution. This  hinge has been developed to suit our swinghandles with article numbers 2400-U1 (RH version) and 2400-U2 (LH version) as well as 2600-U1. Therewith it allows the doors to be turned.

Product description / Product benefits

  • Hinge frame part made of plated steel with press fit threaded studs
  • Hinge door part made of raw steel (weldable)
  • Hinge pin made of plated steel, removeable for easy demounting of the door
  • Concealed hinge for prominent door with door return of 25 mm
  • Useable on both right and left hand side
  • 120° opening angle

The hinge frame part with its press fit threaded studs can be screwed to the frame by means of safety nuts easily and quickly. In return, the hinge door part can be welded to the door using the two destined weld-on pips.
Online Catalogue page 4A-136

Slide shoe for cam

EMKA's new slide shoe for all common steel and stainless steel cams protects the cabinet frame from damage caused by steel-to-steel contact of cam to frame.

Product description / product benefits

  • Tool-free assembly and disassembly on all common cams (steel / stainless steel)
  • The slide shoe prevents scratches on the cabinet, therefore no paint or material abrasion
  • Improved closing behavior and lower closing torque due to its good sliding characteristics


The slide shoe is easily attachable to all common steel and stainless steel cams. Please note: The shoe increases the height dimension (H) of the cam by 2 mm! By using a slide shoe the cabinet frame is not only protected against damages, also the closing torque is significantly reduced due to the avoidance of steel to steel contact– especially with stainless steel cabinets. The same result will be achieved by using the ramp 1000-U858 (Online catalogue page 1C-170).

Online catalogue page 1C-135

Slide shoe for cam
Slide shoe for cam
Quick assembly - simply clip-in
Quick assembly - simply clip-in

Clip-in quarter turn for quick assembly without tools

The quarter turn for quick assembly can be clipped in within a few seconds.

Product features at a glance:

  • Standard cut out 1000
  • Insert part: zamac
  • Three standard height dimensions (H) for Polyamide snap-in pins H=18, H=22 and H=24, each for four different door thickness ranges
  • Further versions of snap-in pins with regard to the height dimension on request
  • Cost saving by tool-less assembly within seconds
  • Basic principle of this patented solution:
    the higher the closing force, the greater the tightness
  • Snap-in pin with safety cap for better insolation of the insert
  • High IP-protection (IP 69K)
  • High safeguarding against overwinding
  • Patented

More information:
Online catalogue page 1B-170
Product sheet



New: Quarter turn for quick assembly
Quarter turn for quick assembly
with 80% less assembly time!
New: Quarter turn for quick assembly

New locking hinge by EMKA

EMKA solution for the HVAC sector

The new locking hinge by EMKA meets all the criteria for securing big air-conditioning units.  By using a height-adjustable hinge bracket, it also makes a precisely adjustable gasket compression possible.

EMKA has based the development of the new locking hinge for the HVAC sector not only on the national and international standards but especially on the RLT guideline 01 of the German AHU manufacturers' association (Herstellerverband Raumlufttechnische Geräte).

When opening the EMKA lock, decompression is effected in two steps: First the door is caught by an integrated, patented impact guard so that the pressure can escape from the vent ducts safely. Then the door is unlocked enabling access to the unit. The door can be closed in only one step, another distinctive feature for convenient handling by EMKA.

Product sheet: HVAC Compression Latch-Hinge

Catalogue page 10A-110:

Also as a short version! Swinghandle series 1325

Clear form language - ergonomic line. EMKA's 1325 has received the iF product design award. New: the shortest version of the swinghandle. Despite the compacter structure, it provides all the benefits of the long version.

  • Variable inserts (round/profile half cylinder, square, triangular, ...)
  • Robust due to glass fibre reinforced high-performance plastic
  • Spring-loaded handle
  • Can be used right and left for within and outside the door gasketing

More information:
Online catalogue page 3BA-210

New: Also a short version! Swinghandle series 1325
Cut-out of the short version! Swinghandle series 1325

New wing knob compression latch

Compression latches are increasingly popular for specialist cabinets and enclosures of all types – whether for their anti-vibrational characteristics or for superior sealing, and this new IP65 wing knob format version offers even wider utility. The wing knob design makes it suitable for a welter of low access security, high sealing protection roles where ingress of dust and water is a problem, but where ready access is required for personnel, for example in high security areas.

Our 1000 wing knob compression latch with IP65 rating comes in 2 types, each with a full 6 mm pull-down. The basic form 1000-U882 is adjustable only by use of different cams – its’ companion 1000-U880 however provides extra depth adjustment with a threaded rod which considerably extends the reach to match extra deep doors or frames.

Please contact us here for details
Links: 1000-U8821000-U880

Program 1022 - Quarter turn for quick mounting

The quick locking system is designed for high-strength and high-density applications and thus ideally suited for boxes and flaps. The locking forces correspond to the well-known 1000 programme.

Product advantages

  • Cost savings within seconds by completely toolless mounting
  • Acoustic and visual control when locking the locking lug
  • Locking force up to 250N (correspond to 1000 programme zinc die version)
  • Smooth handling (concept related no inner tension)
  • high IP-protection (IP 69K)
  • self-sealing design for highest protection claims (concept related)
  • High safety to prevent overrevving
  • Extended capture range/compression of 4.0 mm (1000 programme 3.0 mm standard-cam)
  • Reduced scratch tendency at the enclosure frame
  • 100% corrosion resistant (completely made of PA6 GF30)


New Clip-in hinge

EMKA developed an ingeniously simple, thereby very cost effective but nevertheless very sturdy hinge. The clip-in hinge is distinguished for reaching a high capacity at axial load of 430 N and it is easy to assemble.

Two identical plastic hinge halves complement each other by simply clipping in to a highly resilient hinge.

By screwing the hinge, the clip-in function is suppressed. The hinge halves are highly resilient interconnected.

Product description

  • Plastic hinge consisting of two identical hinge halves
  • Mounting by plugging the two halves together
  • "Pinning" is provided by two spring-loaded pins
  • Spring effect is cancelled by fixation to the frame/at the door
  • Suitable for supporting high radial and axial loads
  • Standard cut out 1056 program
  • Completely made of PA6 GF30
  • Patent protected


New rod guide for round rods

With the program 1001 EMKA developed a new, efficient rod guide for round rods. The rod guide 1001-U47 is designed for 8 mm round rods and can replace the known products
1001-U11 and 1001-U12.

Moreover the installation time is reduced by more than half because of quick assembly. Only plug the rod guide onto the weld stud. Then raise it up. The rod guide perceptibly and audibly locks in place and can be tightened with only a few rotations. After that the rod guide is mounted.

In addition this rod guide is perfectly suitable for raw and powdered weld studs, with the result of a significant optimization of process and cost savings because the covering of the weld stud during powdering is omitted. Corrosion protection remains fully intact.

By simply connecting the rod guide there are two different heights for the common weld stud versions M6 x 16mm & M6 x 20 mm. Depending on the desired height, the lower part is rotated by 90°.

Product description

  • Intelligent plug-in mounting
  • Suitable for raw and powdered weld studs
  • Despite the ultra-smooth fast installation of this application the strength of the overall application is reduced in no way
  • Completely made of PA6 GF30
  • Patent protected

Product advantages

  • Cost saving by smooth, completely toolless mounting within a few seconds
  • Easy use also on powdered weld studs and corresponding cost reduction / process optimization for the customer as the covering of the weld studs can be omitted during the surface treatment and corrosion protection therefore remains fully intact
  • Simplified stock-keeping (1 product for 2 heights)
  • 100% corrosion resistant (completely made of PA6 GF30)

More information...

Rod guide 1001-U47 mounted for weld stud M6x16
Rod guide 1001-U47 mounted for weld stud M6x16
Rod guide 1001-U47 mounted for weld stud M6x20
Rod guide 1001-U47 mounted for weld stud M6x20

3x14 Düz çubular için çubuk yönlendirici

Çubuk yönlendirici, siyah toz boyalı saplamalar üzerinde 100 kg ( 1000 N)'dan fazla bir kavrama gücüne ulaşır. Pinlerin özel koruması olmaksızın saplamalar ile birlikte kapılar tamamen toz boyalı olabilir. Çubuk yönlendirici esnek olarak gerdirilmiştir. Sökülmesi için, sadece kayış dişli yüzeyi üzerinden kaldırılır. Düz çubuğun hızlı montajı için yönlendirici üzerinde bir sap kısmı kullanılabilir. Çubuk yönlendirici, düz çubuk üzerindeki uygun delik sayesinde özel olarak konumlandırılabilir. Özel dizaynı sayesinde çubuk yönlendiriciler tıkırdamaz. Kapı çarpması vs. durumunda çubuk yönlendiriciler düşmez.


Program 1000 Compression latch „Double Red“

Double security and more comfortable handling when opening and closing cabinets, doors and covers: EMKA Double Red, the new closure with double opening indicator offers all of this. The solution is especially tailored to the numerous storage boxes in caravans. Thanks to the innovative closure technology it is also suitable for additional applications in the sectors of industry and transport.

Product description

  • standard market storage box locking systems 1:1 replaceable
  • 2 clearly visible opening indicators
  • locking only in closed position
  • shock and vibration-proof according to DIN EN 61373
  • compression path 6 mm

More information...

Yuvarlak silindirli kabin kilidi

Güçlü müşteri talebi sebebiyle EMKA, 1130-U7 kabin kilidini tekrar başlatma kararı aldı. Düz tasarım ve hem kilitlenebilir hem de su geçirmez olması bu kolun avantajlarıdır. Bu kol çeşitli alanlarda kilitlemelerde kullanılabilir ( örneğin; mekani k tasarımlar, ulaşım, kabinler, vs. ).   

 Ürün Tanımı

  • Kapı kalınlığı 1 – 5,5 mm
  • Düz tasarım (5,5 mm)
  • Geri çekilebilir kol sağ ve sol olarak uygulanabilir
  • Farklı seviyelerde iki köprü kelepçe
  • Büyük kapı kalınlıkları için uygulanabilir
  • Büyük sıkma alanı (1,5'den 57 mm'ye)
  • Entegre edilmiş yuvarlak silindir ile kilitlenebilir
  • IP65


Compression latch with visual open status indication

Shock and vibration-proof according to DIN EN 61373

Even from a distance, the open status is visible by a surrounding red ring.
Available with dust cover, which can only be mounted if the latch is in locked status. 

Security. Visible.


Dust cap for high-speed trains

With the cap installed, protection class IP65 is achieved. Material selection meets the high requirements with regard to UV resistance and aging. The holding force was proofed by a wind tunnel testing at 450 km/h over 15 min each from 4 directions. A vibration and shock-test according to DIN EN 61373, category 1, class B (enhanced test conditions) completes the ambitious test procedure

The cap fulfils the highest requirements regarding the protection of the interior locking system. In conjunction with the compression latch with visual open status indication the cap will not lock while the compression latch is open and by this means the unsecured lock is visible at any time.

New: Program 1000 - Stainless Steel Compression Latches for Hygienic Areas

In addition to the well-established quarter turn for hygienic areas 1000-U838, EMKA has now included the compression latches for hygienic areas 1000-U861 and 1000-U862 in its range of products. As in the case of 1000-U838, the components of the 1000-U862 that are outside the appliance meet the hygiene requirements and the relevant specifications of the BGN (German "Berufsgenossenschaft Nahrungsmittel und Gastgewerbe" - statutory accident insurance institution for foods, hotels, restaurants and catering) Furthermore, the compression latch for hygienic areas 1000-U861 complies with these also inside the appliance.

Product benefits

The stainless steel compression latches for hygienic areas comply with the relevant standards for hygienic areas
DIN EN ISO 14159
, DIN EN 1672-2, DIN 10516
and meet specifically the following requirements:


  • easy to clean surfaces
  • maximum possible radiuses, avoiding cracks and nooks, undercuts and open hollow spaces
  • optimum fit of the gasketing (on the door sheet metal)
  • complies with the IP rating IP 69K

More information...

180° hinge stainless steel

for Ts 1.5 or 2.0 mm

A lift-off hinge made of stainless steel precision casting with an opening angle of 180°. It is designed for an application with framework constructions for prominent doors with a bending of 20 mm. The hinge is available for door gauges (Ts) of 1.5 or 2.0 mm.
Program 1110




Program 1317 Swinghandles for Outdoor Applications

Exposure to the elements all year round, vibrations on the roadside or vandalism - outdoor switch cabinets are exposed to increased stresses. To protect theses boxes EMKA has developed the outdoor program 1317.

With its robust swinghandles EMKA provides a wide range of solutions: from the cost-efficient plastic variation up to the high-quality electromechanical lock of zinc die cast. The whole range was developed in the in-house technology centre. With regard to the design the focus was put on the special tightness and increased vandalism protection of the locks. The clearances between handle and dish have been made so small that no screwdriver fits in. In addition, the surfaces are as smooth as possible so that no dirt can accumulate or graffiti adhere to them.

Product description

  • Single cylinder and double cylinder swinghandles
  • 2 cut-outs (2 square 46 x 46 mm cut-outs at a distance of 105 or 130 mm).
  • All versions in zamac or glass-fibre reinforced plastic
  • In addition to the mechanical version, electromechanical versions are also available for the single cylinder swinghandle
  • The standard surfaces are black powdered or agate grey (RAL 7038) with anti-graffiti coating
  • Versions for 40 mm and 45 mm profile half cylinders as well as Kaba cylinders are available
  • Regarding the electromechanical version, the profile cylinder can be replaced by a blind plug or be used for the mechanical override
  • The double cylinder swinghandle is opened by activating one of the two half cylinders (OR principle).

Product advantages

  • Thanks to their robust design, the swinghandles in the zinc-die version meet the requirements of “WK2” ("RC2, resistance class 2, protection against vandalism) according to DIN V ENV 1630
  • shock and vibration proof according to DIN EN 61373
  • protection class IP 65
  • Great flexibility regarding price-performance ratio due to the wide range of models available
  • tested and approved by Deutsche Telekom


Program 1185 Kollu kilit - dil veya mekanizma için

Bu yeni kollu kilit saysinde güçlü zamak versiyon, düz asarı ve şık bir kolla 1185 program tamamlanmış oldu. Böylece, kullanımı açık alanlarda da mümkündür. Bir mekanizma veya dil kullanımı sayesinde uygulama alanları için limit belirleme zordur.

Uygulama alanları

Açık ve kapalı alan kabinleri, vb. 

 Ürün avantajları

  • Ek bir basma düğme ile açmak mümkün
  • Asma kilit takarak ek bir kilitleme mümkün
  • Dil eya mekanizma kullanımı mümkün
  • Kilidi açmak için basma düğmeyi açan yuvarlak silindir
  • Kollu kilidin IP65 sızdırmazlık özelliği vardır
  • Vandalizme karşı dayanıklı


1317 Tek silindir-kollu kilit

Yeni tek silindir kollu kilit WK2 DIN V ENV 1630 testini ( RC2, Dayanıklılık sınıf 2 testi ) başarıyla geçmiştir. Profil yarım silindir ( 40 ya da 45 mm ) yanısıra KABA versiyonu da mevcuttur. Elektromekanik versiyonda kilitleme silindiri boş tıkaçla değiştirilmiştir. Kurma aşamasında, daha önce bahsedilen kilitleme silindiri mekanik kullanım için montaj edilebilir.


  • Avantajları ve müşteri faydaları
  • Tek silindir kollu kilitler dış mekan uygulamaları için dizayn edilmişlerdir. 40-45 mm profil yarım silindir yanında KABA silindir de kullanılabilir.
  • Kol yapışmalıdır ve 2-12mm'ye kalınlıkta kapılara kadar uygulanabilir.
  • Diğer kapı ölçülerine göre kollu kilitler mevcuttur.
  • Kollu kilitler siyah toz boyalı yüzey veya gri (RAL 7035) antigrafiti olarak mevcuttur.

Uygulama alanları

Bu kollu kilitler iç ve dış uygulamalr için kullanılabilir (energi trafoları gibi)

Program 1325 Swinghandle with variable locking system

The product program 1325 is the successor system to the tried and trusted programs 1125 und 1225.
The new swinghandle 1325 range will prove itself with its technology advances and superior design quality of EMKA as well as sophisticated ergonomics. All these advantages, combined with functional innovation, such as the locking system which can be exchanged quick and easily, have led to our success with “IF PRODUCT DESIGN AWARD 2013”.

Product description

  • for the classic cut out 50-50-50 (inside and outside the gasketing)
  • bending area 45 x 25 mm
  • flat design (30 mm)
  • IP 65 (When mounting within the interior using a cap)
  • IP 40 (quick assembly by hook mounting)

Product advantages

  • variable locking systems
  • robust thanks to fibre reinforced high-performance plastics
  • smooth running with high operating convenience
  • constant pivoting radius, independent of the mounting type
  • optimised haptics
  • integrated scratch protection to avoid surface damage (handle / dish)
  • patented innovative design (award-winning)