The new single cylinder swinghandle has successfully passed the WK2 DIN V ENV 1630 test (RC2, resistance class 2 tested). Versions for profile half cylinder (40 or 45 mm) as well as for KABA-cylinders are available. In the electromechanical version the locking cylinder is replaced by a blank plug. During the construction phase previously mentioned locking cylinders can be mounted in addition for mechanical override.
Advantages, customer benefits
Fields of application
This swinghandle is used for indoor and outdoor enclosures as well as for energy utilities substations.
Because of its robust construction, it is suitable for outdoor use. 40mm and 45mm profile half cylinders may be used. The handle is sealable and can be used for door gauges from 2 to 12 mm. Swinghandles for other door gauges are available upon request. There is an additional version available for non-removable keys in the unlocked state. The swinghandle is available with black powder coating surface finish or in grey (RAL 7035) with anti-graffiti coating.
With the cap installed, protection class IP65 is achieved. Material selection meets the high requirements with regard to UV resistance and aging. The holding force was proofed by a wind tunnel testing at 450 km/h over 15 min each from 4 directions. A vibration and shock-test according to DIN EN 61373, category 1, class B (enhanced test conditions) completes the ambitious test procedure
The cap fulfils the highest requirements regarding the protection of the interior locking system. In conjunction with the compression latch with visual open status indication the cap will not lock while the compression latch is open and by this means the unsecured lock is visible at any time.
Shock and vibration-proof according to DIN EN 61373
Even from a distance, the open status is visible by a surrounding red ring.
Available with dust cover, which can only be mounted if the latch is in locked status.
The rod control consists of three different plastic parts and can be mounted fast and easily. The rods can be clipped-in. The rod control has a very smooth running because of the material combination chosen (different high-performance plastics). The outstanding running characteristics are based on the involute toothing. The precise end stop should be emphasised which does no longer depend on the „flattened“ teeth of the gear wheels but is guided over a large area into the enclosure. All parts consist of high-performance plastics: no corrosion and no metallic clatter (nor with regard to the clipped-in rods), because of stiff (joint-free) clip connection and a high level of stability. Wing knob, T-handle and L-handle remain in defined position. Very suitable for cabinets, where only one, top or bottom, rod can be used as well as cabinets with multipoint locking.
The frame-side leading ramp eases locking and the fixing of the cam into the locked position.
Abrasion will be completely avoided. Therefore, no corrosion occurs on the frame of the cabinet as the frame is not damaged.
The pressure on the gasket can be increased by:
Part No.: 1000-U858
The rod guide also reaches high grip forces of more than 1.000 N on powder coated weld studs. The doors can be powder coated together with the weld studs completely without special protection of the pins. The rod guide is flexibly pretensioned. For dismantling, the strap is simply lifted out of the thread flanks – simple disassembly. A lug at the rod guide can be used for the fast mounting of the flat rod. The rod guide can be positioned specifically by a corresponding bore in the flat rod. Thanks to the constructive design of the rod guide the flat rods do not rattle. The flat rods do not fall out of the rod guide when slamming the doors with extended rods.
For 105 mm hole spacing EMKA could only provide various swinghandles with 46 mm round cut-outs so far. The product scope has now been completed by a swinghandle suitable for a □ 46 mm square cut-out. The □ 46 mm square cut-out with 105 mm hole spacing has a new rear cap. This handle features the same functions as swinghandles 1107-U159-G and 1107-U169-G for the round cut-out.
This swinghandle is used especially for cabinets and enclosures for outdoor applications, especially in harsh environment but also for indoor areas in case of increased requirements for corrosion resistance and hygienic demands.
Technoloy (function, standards, patents, etc.)
The handle withstands a 720 hours salt spray test and has successfully passed the IP66 test. A torque up to 46 N·m can be transmitted by the turned shaft.
Advantages, customer benefits
Due to its material properties this swinghandle defies corrosive influences. A torque up to 46 Nm can be transmitted. The handle is suitable for cams and rod control systems series 1121 and inside or outside the gasket. Some versions of this swinghandle support the push to lock feature, ref. to catalogue page 8A-632. The cutout complies to the 25 x 150 mm standard.
Design of a compression latch for small mounting spaces.
With a housing height of 18 mm the compression latch is suitable for door gauges from 1.2 up to 8 mm.
Suitable on doors and hatches exposed to high vibration; shock tested according to DIN EN 61373
Direct replacement of standard quarter turns is possible.
The rod control of the lift-handle has been changed to guide the steel or aluminium rods vertically to the door leaf. This leads to an increased mechanical stability of the complete locking system and a higher tearing force. The number of the rod guides and catches will be reduced compared to the traditional version with the plastic rods. Different door heights are met by shortening the rods without losing a locking point. More information you will find on catalogue pages:
3F-320 Lifthandle Program 1190
3F-330 Lifthandle Program 1190
3ZA-560 Rod Program 1190
Due to high customer demand, EMKA has extended the 160° hinge program 1056 by four variants. The screw-on hinges zinc-die (hinge pin zinc-plated) can be delivered ex stock with surfaces black powder coated or chrome plated. Hinges for flush doors are lift-off versions and can be mounted very easily by hexagon nuts.
EMKA has set up new tools for the developed and well established POS hinge for chests (e.g. refrigerating chests). This hinge is freely obtainable and available for different spring loads. The hinge can be regulated according to the weight of the lid (of the chest) by means of an adjusting nut in the socle, so that the lid remains in any position. The covers that are included in delivery can be put on easily after assembling of the hinge. The spring-loaded hinge for a lid weight of about 6 kg – 23 kg is now available.
Compared with ours pulls (No. 1091-103-01, 1091-103-02 and 1091-103-03) the new parts have essential advantages:
Furthermore, both variants allow an application of the company logo by multicolour pad printing. Program 1091more
A new variant has been added to our well-established hinge program 1079: a stainless steel lift-off version according to AISI 316 (1.4401). The new variant shows a specific characteristic: The chamfered ends prevent an accumulation of dirt, so that this hinge can not only be used in the sector of sheet metal forming, but also for other applications, e. g. in the food industry. The 180° hinge is suitable for right hand as well as for left hand application and is suitable for prominent doors.
EMKA is expanding the product range of 1250 (window) by a series of windows with casted on mounting bolts. The windows are provided with a captive circumferential and foamed seal so the windows are IP 65 rated. Windows without frame are available for a door thickness (Ts) of 3 to maximum 13 mm, windows with frame are available for a door thickness (Ts) of > 1 to maximum 6 mm.
The EMKA hinge series was expanded by a new small type of screw-on hinge. This screw-on hinge for M4 countercunk screw is made of zinc-die casting, the dimensions of 30 mm x 30 mm make it especially suitable for small hatches. The hinges are available with chrome-plated or black powdered surface. For different variants, please, contact EMKA.
Pin hinge is applied in the area of e.g. electricity meters or tool boxes. Beside the already existing version for Ts 1,00 mm we now provide two additional types for Ts 1,5 or 2,0 mm.
The latch is specially made for steam-tight oven doors and may be regulated by an adjustable clamp. All visible surface areas are ground, polished and then chromium plated. It is the chromium plating of the surface areas that sanitizes this latch and allows a riskless use with production machines, e.g. of the food industry.
for Ts 1.5 or 2.0 mm
A lift-off hinge made of stainless steel precision casting with an opening angle of 180°. It is designed for an application with framework constructions for prominent doors with a bending of 20 mm. The hinge is available for door gauges (Ts) of 1.5 or 2.0 mm.
As a special product for customers of the railway sector we developed the so-called key „Bundesbahn“. It fits with all typical „Bundesbahn“-inserts. The key is internationally well-established at companies of the railway sector.The key is available in GD-Zn or stainless steel.
Agent E is a battery-operated electro-mechanical handle module which can be installed instead of a usual handle or quarter turn. It takes over the functiononality of the lock. Three different versions of Agent E are available (Basic, Professional, Superior).
Release and programming is effected via micro transmitter (TAG) with an encoded light beam, directed to a receiver cell inside the handle module
The version Professional allows programming of Agent E via USB port. Event memory (opering and locking activities) can be read out.
The version Superior allows a central administration of all functions with software AGENT E Management Suite via radio network and the system-specific access point. more